This submit about how to make three Quick Do it yourself Floating Photo Frames And How to Reduce Plexiglass is sponsored by The Residence Depot as component of the #THDProSpective Method. It also is made up of affiliate links. See policies.
Uncomplicated Do it yourself picture frames are really one of my most requested tutorials and oddly more than enough, until eventually now, I didn&rsquot have quite a few to share!
.
I actually created my dad a big Do it yourself custom photo frame as a Xmas gift a couple years back and shared the tutorial for it below. But it applied dowels, and a router, and it may perhaps have been a minimal a lot more associated than most individuals are on the lookout for.
So, in this post, I&rsquom going to show you how I created three distinctive type Super Uncomplicated Do-it-yourself floating photo frames with just two standard tools. I&rsquoll also display you how straightforward it is to reduce plexiglass for them, far too!
.
So if you&rsquore ready to get creating, allow&rsquos go! I&rsquove obtained the video tutorial here and the stage by action below:
Tools AND Supplies:
- Miter noticed (or any wood reducing noticed is good&ndashdoesn&rsquot have to be a MITER observed)
- Nail Gun (optional, just tends to make things more quickly)
- Wooden Glue
- ¾&Primary sq. dowels
- one×2 boards
- ¼&Prime x one ⅛&Key lattice trim
- Slender Plexiglass Sheets
- Ryobi One+ HP Minimize Off Instrument (employed to slice plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in location of clamps to keep parts even though wood glue dries)
- Turn buttons
A Notice About FLOATING Picture Frames:
I&rsquom sharing how to make 3 diverse design FLOATING image frames in this tutorial, but the to start with move to earning any of them is reducing the plexiglass to the sizing you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this stage. But due to the fact the graphics/pictures I framed are &ldquofloating&rdquo inside of the frame, they&rsquore in essence sandwiched involving two parts of plexiglass. So plexiglass/acrylic is vital to be able to &ldquofloat&rdquo your photograph.
.
To make items straightforward to adjust out in these frames, I also employed these convert buttons&mdashor I phone them twisty tabs&ndashon the back again to maintain the plexiglass in spot.  
HOW TO Minimize PLEXIGLASS
Typically, I have my regional glass shop minimize my glass and plexiglass pieces for my initiatives.  But since these plexiglass items will be compact and several customized sizes, it would be much more affordable, quicker and less complicated to just slash them myself.
.
I employed some (about) ⅛&rdquo acrylic sheets from House Depot.  They appear in a variety of dimensions, all the way up to a 4×8 sheet.  I just grabbed some 11x14s.
I built some simple graphics on my computer (PicMonkey and Canva are wonderful for this!) and also used a patch that I received a number of several years ago at a conference for these frames.  You can use a photograph, a poster, material, whatsoever you want to body for this.
.
I laid them out on my sheet how I appreciated the spacing, then marked wherever I preferred to lower&ndashno measurements here&hellipjust eyeballing how I imagined the spacing close to the impression seemed fantastic.
Now, I&rsquove made use of the low-cost minimal hand knife they claim will slice plexiglass prior to and it was a horrible knowledge with very lousy outcomes.  I&rsquove also applied a jig observed to minimize plexiglass and it melts, gets stuck, then chips or cracks the sheet.
.
So THIS time, I experimented with this new Ryobi One+ HP Compact Slice Off Tool with a plastic chopping blade and was extensively impressed with how brief and clean up the cuts were.
When I very first noticed this tool, I found it variety of strange searching.  But right after I used it, I recognized the thought. 
.
It&rsquos in essence a hybrid amongst a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety levels. 
.
It&rsquos compact and light-weight and it&rsquos acquired a ahead and reverse switch to convert the blade each directions.  It&rsquos also received a variable velocity cause&mdashwhich is great for cutting plastic to enable avoid melting. 
It comes with a plastic and drywall blade, a metallic minimize off wheel, and a diamond blade for chopping tile and cement board.  You can find out far more about the new Ryboi One particular+ HP cut off instrument at the hyperlink listed here if you&rsquore intrigued.
.
For slicing straight traces on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the metal blade guard in opposition to it to make the slice.  You can skip the straight edge and freehand these cuts, as well if you have a constant hand. (I don&rsquot haha!)
I did uncover it slice finest in this situation with the change in reverse. It seemed to not soften that way.
.
I slash two items similar in measurement for each individual product I was framing. Then, I was ready to start out generating the actual floating photograph frames.
Easy Do it yourself FLOATING Image Frame Style one
Type one is my private beloved, so I&rsquoll commence with it 😊
This individual floating picture frame layout demands ¾&Key square dowels and one×2 board. It is basically just a one×2 wrapped around a square dowel body.
.
I applied ¾&rdquo sq. dowels for this and set up my miter saw to lower forty five degrees.  Now, you don&rsquot have to miter these.  You can go away it on 90 and make butt joints.  You also don&rsquot will need a MITER saw for this.  Any saw that you can slash quite straight with will operate wonderful.
.
I generally trimmed four pieces of sq. dowel so that when suit with each other, they&rsquod be just hardly (like ⅛&Primary) greater than the plexiglass piece I was putting in it.
I used wooden glue to the corners and nailed them collectively with brad nails.  If you are patient, and don&rsquot have a nail gun, simply glue and clamp till dry.
.
Following the glue experienced dried, I lower to fit 1×2 items with 45 diploma mitered corners about this body.  Again, butt joints are wonderful here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s all-around the edges leaving about ¼&rdquo sticking out the back side of the plexiglass, so that when I install the two ⅛&Primary plexiglass parts, it&rsquoll be flush across the back side of the body.
Then, I screwed these twisty tabs into the back again sides of the body to maintain the plexiglass in location.  I&rsquoll go back again and thoroughly clean navigate here off the plexiglass later, but for now, I set this off to the side to make the following frame.
Easy Do-it-yourself FLOATING Image FRAMES Model 2
Style 2 is a small simpler and is produced of 1x2s and ¼&rdquo thick by 1 ⅛&Key huge lattice trim.
I started by chopping down the lattice pieces so it would make a frame that the plexiglass would in good shape Within.  Yet again, just like ahead of, the mitered corners are optional.
The moment I had this lattice body lower, I measured its total size and slash 1×2 pieces to make a body whose in general size matched that of the lattice frame. See below 1×2 frame laying on leading of lattice body&ndashthey&rsquore the similar dimensions.
I glued and nailed the one×2 frame alongside one another and clamped until finally dry. All over again, you can use tremendous glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice body on to the back again.  I utilized a major item to maintain it in area until finally it was dry, then, I screwed twisty tabs on the back to maintain the plexiglass in area. 
Since the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass items are positioned inside, all the things should really sit flush across the again just like the very last frame.
Once more, I&rsquoll go back again and cleanse the sawdust off afterwards, but for now, I moved on to the last type body.
Easy Do it yourself FLOATING Photo Body Style 3
Model 3 is the exact strategy as model 1, but alternatively of utilizing 1x2s, I employed ¼&Prime x 1 ⅛&Key lattice trim to keep the body a minimal thinner and much more minimalist hunting.
So, I minimize ¾&rdquo square dowels to make a body the exact same sizing or a little more substantial than the plexiglass I was framing and glued and nailed it alongside one another.
Then, I slash lattice trim to wrap close to that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back again side of the square dowel frame so that when the two pieces of ⅛&rdquo plexiglass are installed, it&rsquoll all be flush across the again.
.
I didn&rsquot have any brad nails small ample to nail this body on, so I simply just glued and clamped until eventually it was dry.
If you don&rsquot have clamps, you can use painters tape to variety of wrap around the parts to maintain until finally the glue dries OR merely use some tremendous glue or CA glue to support keep pieces in place right up until the true wood glue is treated.
.
Then, just like the last two frames, I set up twisty tabs to maintain the plexiglass in location.
FLOATING Picture Frame HANGING Choices
The final stage is cleanse up and hanging.  I utilised some glass cleaner to thoroughly clean up all the saw dust, then employed a piece of double sided tape on the back again plexiglass piece to make sure the pics keep in position, then place the frames again alongside one another.
.
To hang, you can use your standard sawtooth hangers for this.
Or merely area it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and hang it on a piece of wooden dowel you screwed into the wall.
As you can see, building photograph frames doesn&rsquot have to be intricate.  This is a terrific beginner venture you can deal with with minimum equipment and get as artistic as you want. 
.
I in fact hung these graphics up in my desk location to aid keep me inspired while working by yourself from dwelling appropriate now. So, now that my desk room is full, I guess I really should most likely get back again to do the job 😊
I hope you&rsquove loved this minimal undertaking.  There are a good deal far more coming your way, so be positive to subscribe to my publication under so you don&rsquot skip out on what&rsquos coming following!
.
And don&rsquot overlook to pin this for later on!
Until finally following time, joyful building 😊